COTTON HAMMOCK
WITH FRAME
90975
ASSEMBLY INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
©
®
Copyright 2004 by Harbor FreightTools . All rights reserved.
No portion of this manual or any artwork contained herein may be
reproduced in any shape or form without the express written consent
of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
6. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use
accessories intended for use with this tool. Approved accessories are available
from Harbor Freight Tools.
7. Do not use or assemble under the influence of alcohol or drugs.
Unpacking
When unpacking, check to make sure the following parts (shown on page 5)
are included. If any parts are missing or broken, please call Harbor Freight Tools at
the number on the cover of this manual.
Assembly
1. Locate both Bases (2). Place each Elbow (3) over each Base (2), line up the
bolt holes, and fix in place using the 4 sets of Elbow Nuts and Bolts (5).
See Figure A.
Riser (1)
Center Joining
Tube (4)
Center Joining
Tube Bolt (6)
Elbow (3)
Base (2)
Elbow Nut
and Bolt (5)
Figure A
2. Select a surface that will not scratch the finish of the frame. Place both Elbows
(3) on each side of the Center Joining Tube (4) so that the horizontal ends are
on the inside. See Figure A.
3. Insert the Center Joining Tube (4) over the lower part of one Elbow (3) as far as
it will go. Line up the Center Joining Tube Bolt (6) with the notch on the Elbow
and tighten partially. Repeat on the other side. Tighten both Center Joining
Tube Bolts securely. (Check for tightness periodically). See Figure A.
4. Attach Square End Caps (7) onto both ends of each Base (2). See Figure D.
5. Insert the Risers (1) over the upper part of the Elbows. Be sure the notches for
hanging the Hammock (9) are facing inwards. See Figure B. The Risers (1)
should rest on the Ring Stopper on the Elbow ( 3). See Figure C.
SKU 90975
Page 3
Metal Rings
Round End Cap (8)
Ring Stopper
Riser (1)
Elbow (3)
on Elbow (3)
Notches
Facing
Inside
Riser (1)
Figure B
Figure C
6. Hook the Metal Rings on the Cotton Hammock (9) (left and right) over the
Notches. Test to see that Hammock is securely attached before getting into
the Hammock. See Figure D.
7. Attach Round End Caps (8) onto the ends of the Risers (1). See Figure B.
Cotton Hammock (9)
Metal Rings
Metal Rings
Figure D
Square End Caps (7)
Maintenance
1. When cleaning, wipe Cotton Hammock with a soft damp cloth. Dry thoroughly.
2. Dismantling and storing during harsh weather will prolong the life of the
Hammock.
SKU 90975
Page 4
PARTS LIST
PART
DESCRIPTION
QTY.
2
1
2
3
4
5
6
7
8
9
Riser
Base
Elbow
2
2
1
Center Joining Tube
4 sets
Elbow Nut and Bolt
2
4
2
1
Center Joining Tube Bolt
Square End Caps
Round End Caps
Cotton Hammock with Wooden Spreaders
NOTE:Some parts are listed and shown for illustration purposes only
and are not available individually as replacement parts.
8
9
1
5
2
7
6
4
6
3
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE
MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY
OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS
TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF
THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES That ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS
OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
SKU 90975
Page 5
|