Model H8088
2-Stage
Transmission Jack
Specifications
Maximum Lifting Capacity .................. 1,100 Lbs.
Lifting Range ........................................34"–713⁄8
"
Weight ................................................... 138 Lbs.
Assembly
Refer to the parts breakdown on the back of this
page to understand how the jack is assembled.
Platform
Adjustment Knobs
Operation
Figure 2. Platform adjustment knobs.
Pump Control Handle (Figure 1): Point to the
left to allow the jack platform to lift when pumped.
Point to the right to lower the jack. (If the jack
holds a heavy load, turn very slowly to control the
lowering rate and avoid dropping the load.)
This jack is designed to assist in transmis-
sion removal only. Failure to follow these
instructions when using the transmission
jack could result in serious personal injury
or death:
Foot Pedal Pump (Figure 1): When moved up
and down, the foot pedal pump lifts the jack plat-
form.
1. ALWAYS support the vehicle with appro-
priately rated support stands before
using this jack.
2. Only use this jack on hard level sur-
faces such as concrete or asphalt.
3. DO NOT overload this jack beyond the
maximum lifting capacity. Overloading
can cause the jack to collapse.
Pump
Control
Handle
4. DO NOT use this jack to lift or support a
vehicle.
5. Keep fingers and hands away from
pinch points when lowering.
Pump
Foot
Pedal
6. Only transport load with jack platform
in the lowered position.
7. Center the load on the jack for stability
and use safety chain to secure load.
Figure 1. Pump controls.
Platform Adjustment Knobs (Figure 2): Located
under the jack platform, these knobs allow for pre-
cision placement and leveling of the platform.
If you need help with the Model H8088, call our
Technical Support line at: (570) 546-9663.
COPYRIGHT © DECEMBER, 2006 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#TR8855 PRINTED IN CHINA
H8088 Parts Breakdown and List
��
��
�
��
��
��
��
��
����������
�
��
������
��
����������
��
��
�
��
��
��
��
��
�
�
��
�
��
�
����
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
PH8088001
PH8088002
PN09M
CASTER
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
PN02M
HEX NUT M10-1.5
STEEL BALL 5MM
SET SCREW M6-1 X 10
COLLAR
2
LEG
PH8088018
PSS01M
3
HEX NUT M12-1.75
4
PLW05M
LOCK WASHER 12MM
HEX BOLT M12-1.75 X 70
PUMP ASSEMBLY
PH8088020
PWN02M
5
PB140M
WING NUT M8-1.25
HOOK BOLT
6
PH8088006
PH8088007
PH8088008
PH8088009
PR06M
PH8088022
PH8088023
PH8088024
PH8088025
PH8088026
PH8088027
PH8088028
PH8088029
PW01M
7
PLATFORM ASSEMBLY
CHAIN
STUD PIN
8
ANGLE IRON PIECE
CORNER METAL PIECE
EYE BOLT
9
FOOT PEDAL
10
11
12
13
14
15
16
EXT RETAINING RING 16MM
HALF CIRCLE HANDLE
FOOT PEDAL PIN 66MM
HANDLE PIN
PH8088011
PH8088012
PH8088013
PH8088014
PB32M
ANCHOR SHACKLE W/SCREW
COTTER PIN 3 X 35
PIN 76MM
STRAIGHT HANDLE
HEX BOLT M10-1.5 X 25
FLAT WASHER 10MM
FLAT WASHER 8MM
MACHINE ID LABEL
FILL BOLT
PH8088031
PH8088032
PW04M
The machine ID label warns about hazards and ways to prevent injury. The owner of the jack
MUST maintain the original location and readability of the label. If the label is removed or becomes
�����������������������������������������������������������������������
�������������������������������������
������������������������������������
�����������������
��������������������������������
���������������������������������
����
�����������������
����
������������������
|